Accessories for immersion heaters

view style:

View: 12 24 ALL


show blocks helper

Product High stop Temperature (°C)

Product Holding temperature (°C) Th

  • Adjustable electronic manual reset limiter for immersion heater IP66, IK10

    -Equipment requesting a very strong resistance to water ingress. The transparent cover allows to visualize the set point and the 2 pilot lights Fully wired electronic temperature control sub assembly for direct mounting on immersion heater elements, 1”1/2 or M45x2 with double thread or rotation ring. Applications in high temperature safety in usual industrial applications…

  • Deep drawn immersion heater fitting

    304L or 316L stainless steel, with gasket and rotation ring for 1, 2 or 3 heating elements This set, more economical than machined solutions, allows the installation of an immersion heater entirely of stainless steel on any enclosure, and requires only a dia. 75 mm drill on the bottom of the enclosure, the same as…

  • Electronic thermostat for immersion heater IP66, IK10

    -Equipment requesting a very strong resistance to water ingress. The transparent cover allows to visualize the set point and the 2 pilot lights Fully wired sub assembly for direct mounting on immersion heater elements, 1”1/2 or M45x2 with double thread or rotation ring. Applications in usual industrial applications and environments, non-hazardous areas. -Very small differential

  • Elevated terminal plastic connection blocks

    In electrothermal connection applications, especially in immersion heater connection boxes appear specific constraints: high ambient temperature, frequent thermal cycles, and confined space around the ends of the heating elements and their terminals, making difficult to the user to make connections. These terminals have been developed to address these constraints.

  • Enclosure for immersion heater, level sensor or temperature sensor, Y304

    - Can receive a drill on the back for 1"1/4, 1"1/2 and M45x2 fittings with double thread and inner nut, or single thread with rotating ring - Can receive a 2" double thread fitting (only with thread on the enclosure) - Can receive a drill on the back for temperature sensor or level sensor -…

  • Enclosure for immersion heater, Y305

    - Can receive a drill on the back side for 1"1/4, 1"1/2 and M45x2 fittings with double thread and inner nut, or single thread with rotating ring - Can also accommodate a 2" double threaded fitting (only with threaded ring) - Has mounting bosses for internal adjustment backplate - Output via an M20 or M25…

  • Immersion heater thermostat temperature control IP66, IK10

    Applications -Equipment requesting a very strong resistance to water ingress. The transparent cover allows to visualize the set point and the 2 pilot lights Fully wired sub assembly for use on immersion heater elements, 1”1/2 or M45x2 with double thread or rotation ring. Applications in usual industrial applications and environments, non-hazardous areas.

  • Manual reset immersion heater limiter IP66, IK10

    -Equipment requesting a very strong resistance to water ingress. The transparent cover allows to visualize the set point and the 2 pilot lights Fully wired sub assembly for use as high limit on immersion heater elements, 1”1/2 or M45x2 with double thread or rotation ring. Applications in usual industrial applications and environments, non-hazardous areas.

  • Miniature enclosure for immersion heater, level sensor or temperature sensor, Y303

    - Can receive a drill on the back side for immersion heater fitting up to 1"1/2 (double threaded model, only with case tapping) - Can receive a drill on the back side for temperature sensor or level sensor - Output by M20 cable gland

  • Miniature enclosure for temperature sensor, level sensor, electronic printed circuit or cartridge heater, Y301

    - Can accommodate ½" threaded fittings with internal lock nut or ¾" or 1" brass fittings with 2 x M4 screws (Use a flat gasket) - Includes a removable internal 3-way 2.5mm² terminal block - PG11 cable gland outlet

  • Polypropylene immersion heater enclosure for highly corrosive environments, Y3C7

    Screws: There is no external screw in this housing. Cover: Screwed cover, with Molded FKM (Viton) fluoroelastomeric polymer, silicone or NBR O-ring gasket. Cover can be tightened by hand or with a double hook wrench.

  • Polypropylene immersion heater tube enclosure for highly corrosive environments, Y3C6

    Screws: There is no external screw in this housing. Cover: Screwed cover, with Molded FKM (Viton) fluoroelastomeric polymer, silicone or NBR O-ring gasket. Cover can be tightened by hand or with a double hook wrench.